INAR-M25 MACHINE FOR TERMINATION OF INAR-RS, INAR-RS MATE

INSERTION MODULE UNIT

The single module unit, to insert INAR-IDC terminals into single or multi-way housings, will be used in a automated assembly system or in a rotary index table .

The insertion of terminals can be made both on ‘closed’ electrical motors (with no visible winding) and on ‘open’ electrical motors (with visible winding) in automatic sequence.

The insertion module unit is composed by two overlapping slides moved by two pneumatic cylinder. One slide with a regulation to adjust the distance to the connector and the other slide with a fixed stroke to cut and insert the terminals. The position of terminals from the strip is done mechanically when the insertion cylinder move forward.

Single or dual feed.

Single, dual, triple and fourth insertion .

The unit has a system to collect scraps, a system to check the pitch, and a system to check the presence of terminals.

Pneumatic and hydraulic systems are not included.

two versions available:

  • M25 A:Single Insertion unit

  • M25 B:Single Insertion unit with programmable linear slide

 

LINEAR BENCH MACHINE

The linear bench machine is designed for the insertion (vertical bench or horizontal bench ) of INAR-RS and INAR-RS MATE terminals in housings with in line cavities (single or multiple) .

The machine can be placed into an automated assembly system adding a system to load or offload the final piece.

Stators, bobbins, are hand held  on pallets that bring the parts in the terminals insertion location to make the wire connection.

The insertion unit of terminals consists of M25 A or M25 B.

Micro processor Controlled

Easy programming through hand-held keypad/display

The unit has a system to collect the scraps.

The unit is built according to the most severe safety standards and it grants the best efficiency on extended use.

Two versions available :

  • M25 1C:single pallet to load and offload.

  • M25 2C: two pallets to reduce the working time (loading a piece while the other one is being processed).

 

TECHNICAL FEATURES

  • Dimension [mm]: 900 x 900 x 1800 h;
  • loading height: 900.
  • Insertion time per each station: 1,5 seconds.
  • PLC Siemens, software for programming with self-diagnostic system.
  • Display touch screen, selection: MANUAL/AUTOMATIC/STEP-BY-STEP.
  • Protection with polycarbonate with aluminium frame placed behind and on the sides.
  • Optical barrier protection placed on the front side.
  • Power Supply : 220V.
  • Air Pressure : 6 bar.

 

ROTARY BENCH MACHINE

The Rotary bench is designed for the insertion (vertical bench or horizontal bench ) of INAR-RS and INAR-RS MATE terminals in housings with angular opposed cavities (single or multiple) .

The machine can be placed into an automated assembly system adding a system to load or offload the final piece.

The insertion unit of terminals consists of M25 A.

Micro processor Controlled

Easy programming through hand-held keypad/display

The unit has a system to collect the scraps.

The unit is built according to the most severe safety standards and it grants the best efficiency on extended use.

Two versions available :

  • M25 1E: single pallet to load and offload the part.

  • M25 2E: two pallets to reduce the working time (loading a piece while the other one is being processed).


TECHNICAL FEATURES 

  • Dimension [mm]: 900 x 900 x 1800 h.
  • loading height: 900.
  • Insertion time per each station: 1,5 seconds.
  • Programmable angle of rotation with tolerance ±0° 10’.
  • PLC Siemens, software for programming with self-diagnostic system.
  • Display touch screen, selection: MANUAL/AUTOMATIC/STEP-BY-STEP.
  • Protection with polycarbonate with aluminium frame placed behind and on the sides.
  • Optical barrier protection placed on the front side.
  • Power Supply : 220V.
  • Pneumatic power: 6 bar.


BASIC BENCH MACHINE

The basic machine is a bench machine with reduced volumes and essential automation technology. It’s suitable for the vertical insertion of INAR-RS and INAR-RS MATE terminals in housings with in line cavities (single or multiple) .

The parts to process (stators, bobbins…) are hand-handle on a centering pallet that allows only two working positions: one for automatic process and one to move the stator at the end of each cycle in case you need to insert terminals in a different position.

The insertion unit of terminals consists of M25 A .

The unit is built according to the most severe safety standards and it grants the best efficiency on extended use.

TECHNICAL FEATURES

  • Dimension [mm]: 700 x 800 x 900 h;
  • loading height: 150.
  • Insertion time per each station: 1,5 seconds.
  • PLC Siemens, software for programming with self-diagnostic system.
  • Display touch screen, selection: MANUAL/AUTOMATIC/STEP-BY-STEP.
  • Protection with polycarbonate with aluminium frame placed behind and on the sides.
  • Optical barrier protection placed on the front side.
  • Power Supply : 220V.
  • Air pressure : 6 bar.

 
 
 

SalvaSalvaSalva